Categories
Bath Shower

Best Showerhead for Low Water Pressure and Buying Guide

Disclaimer: This post contains affiliate links for which I earn a commission.

Note: Before starting, click here to open a new tab in Amazon to search for any tools or equipment that you might need.

Today, you can improve your showering experience by using a low water pressure showerhead. The showerheads enable water to flow out at higher rates, hence giving your powerful streams and improving your showering experience. Ideally, it makes the water stream stronger and comfortable to use.

Generally, low water pressure in your shower head results in a weak stream that is frustrating and inconvenient to use. In most cases, it takes too long to shower, rinse your hair, or shampoo.

Anza low water pressure showerhead

When looking for a shower head for low water pressure conditions, you need to pay attention to various issues. These include the style, pressure, spray modes, durability, and ease of installation and cleaning.

What causes low water pressure in your shower head?

If your system has low pressure, the shower releases very little water such that it takes much longer to shower. It is also very uncomfortable, especially when the amount of water cannot remove the soap properly. The reasons that cause this include, but not limited to;

  • When the plumbing in the house has old pipes
  • Undersized or small capacity pipes
  • A clogged water system, or showerhead. If you are using hard water such as from a well, there are risks of clogging by the calcium deposits.
  • An obstructed or faulty shut-off valve.
  • Using a water-saving or flow restricted shower head.

The solution differs according to the challenge. For example, if it is due to small or old pipes, you need to replace them with large or new ones to improve the flow. Similarly, if it is an issue with the showerhead, you need to unclog or replace it with a good model. For example, you could use a low-pressure shower head that provides a good stream of water even when the flow rate or volumes are low. Also, if your shower head has a restrictor, you could either set it to the maximum or a setting that provides a reasonable water flow rate.

Using a low-pressure shower head to improve water flow

To boost the flow, you need to look for a high-pressure shower head that pushes the water through the jets to provide a strong stream. Generally, a clogged shower head, low water pressure, or other issues are undesirable since they affect the quality of your system. If experiencing such problems, you need to consider installing a low-pressure showerhead. 

The low-pressure showerheads usually have fewer and finer holes. Such a design allows the water to come out of the holes at higher pressures, thus making the water streams stronger. Also, there are adjustable shower heads that enable you to select different spray settings.

9 Best low-pressure showerheads

To help you decide on what is best for you, here are the best low-pressure shower heads.

AquaDance Antimicrobial low water pressure Showerhead

The AquaDance Antimicrobial Shower Head delivers a powerful spray that ensures comfort and efficiency. In practice, the antimicrobial feature prevents the growth of bacteria, mildew, and molds. It has a flexible rubber design that you can clean easily hence prevent the build of calcium and mineral deposits.

The showerhead has six spray settings that allow you to customize according to your preferences. Also, it has a six-inch face that offers a wide area and improved rinsing efficiency.

The showerhead provides excellent performance even under low water pressure conditions. Other features include a choice of six different spray settings, hand shower option, heavy-duty steel hose, rub-clean jets, a large 7-inch rainfall showerhead, and more.

ANZA adjustable low water pressure shower head

The ANZA is an easy-to-install shower head with 76 anti-clogging nozzles to provide consistent and strong water pressure. It has an anti-leak, crack-proof, and heat-resistant design hence offering a reliable and efficient service. The adjustable shower head has six different spray settings for more flexibility. Additionally, the showerhead, which has a 4.7-inch face, is usually available in Oil Rubber Bronze or Brushed Nickel color options.  

Wantba High-Pressure Rainfall Massage Shower Head

The Wantba showerhead provides wide and powerful streams of water that easily cover all your body without having to turn around. It delivers 57 jets and you can adjust the angles to your preferences.

Wantba is a great shower head that helps you to overcome low-pressure conditions by providing you with powerful water streams. It has 5 settings to help you select what works best for you without sacrificing comfort. The showerhead helps you to save water and bills. Easy to install and does not leak,

Further, it is an easy-to-maintain shower head that you can disassemble and clean in only a few minutes.

Fire Hydrant Spa Plaza Massager Shower Head

The Fire Hydrant has a mechanism that compensates for the low pressure to deliver water at a higher velocity. The showerhead is a high-quality Chrome device that is flexible and provides you with the feature to adjust the output and style angles. It has a luxury chrome finish that provides excellent surface protection.

Generally, it allows you to improve your weak or low-pressure shower. Its design amplifies low water pressures to provide you with a comfortable and effective shower. Also, it has adjustable water amplifying feature with several spray settings and patterns.

Aqua Elegante High-pressure shower head

Aqua Elegante is an efficient showerhead that provides superior performance with a strong water stream even in low pressure and hard water conditions. It is a one twist-on shower head that delivers strong streams of water from its 42 nozzles. The showerhead comes with a removable flow limiter that you can remove whenever you require an extremely high water pressure. 

Also, it has self-cleaning spray holes that minimize or prevent mineral or lime build-up, hence reducing clogging and maintenance time. Further, its mineral-resistant silicon material prevents the mineral buildup and clogging of the nozzles.

Niagara Earth Massage Shower Head

The Niagara shower head is a powerful and affordable shower head that delivers a consistent and powerful flow rate through its nine nozzles, including in situations with low water pressure. The high corrosion-resistant, self-cleaning showerhead provides a comfortable shower while reducing water usage by almost 75%. Other than the low purchase cost, the showerhead delivers water and energy savings use thus enabling you to save on your bills.

HO2ME Handheld low water pressure showerhead

The HO2ME shower head is a great handheld device that delivers a strong water spray hence better relaxation. You can use its multi-function feature to choose the right spray strength from a wide selection. 

The HO2ME showerhead provides powerful water streams and hence delivering excellent performance to overcome low water pressure challenges. Also, it has silicon rubber jets that prevent mineral deposits.  

The handheld showerhead has a beautiful Chrome finish that also helps to protect the surface. Other features include easy-to-clean nozzles, a water flow regulator, stainless steel hose, and more.

WASSA High-pressure shower head

The WASSA shower head is a powerful, compact, and lightweight high-pressure showerhead with a superior rain spray and performance. The small and compact showerhead has a Chrome finish and an anti-leak for durability and water savings.

It provides superior and strong sprays even when you have a low water pressure or flow rate. It has self-cleaning silicone nozzles, which help to prevent mineral deposits and hole clogging. Also, it is an easy-to-install device that you can easily attach to the standard shower arm without requiring any tools. 

WASSA High Pressure Shower Head

Other features include anti-leak, adjustable shower arm, removable water restrictor, self-cleaning silicon nozzles, and more.

Triton 5 function shower head

The Triton is a rub-clean, 5-position shower head with a classic and stylish design. It has ABS plastic construction and suitable for use in a wide range of pressures, including low flow rates or levels. The Triton shower head has a Chrome finish and universal fitting. It also provides a choice of 5 spray patterns and pressure variants such as blast, rain, spray, jet, and drench.

Also, you can install the easy-to-clean shower head without requiring any tools. The push and twist spray plate allows you to access and clean hard-to-reach areas. 

How to buy the best shower head for low pressure 

There are many types and models of low-pressure showerheads in the market. These differ in various ways. Some of the shower heads come with adjustable settings to provide you with different pressures and spray patterns. A self-cleaning option is also good since it allows you to reduce the build-up of lime and mineral deposits with minimal maintenance effort.

Ideal features of a low-pressure shower head

In addition to performance, you need to consider other issues such as cost, reliability, mounting options, and others when purchasing your low-pressure showerhead. Today, the market has a wide range of low-pressure shower heads that often differ in terms of spray settings and designs such as rainfall style, self-cleaning nozzles, cost, etc.

Here are some features that make a great showerhead, even when the water has low pressure.

  1. Built with durable materials such as chrome, high-quality plastic, heavy-duty steel, and others
  2. A handheld option
  3. Allows you to adjust settings
  4. Good corrosion-free and visually appealing finish such as Nickel, Chrome, Silver, Oil-Rubbed Bronze, and other materials. 
  5. A heavy-duty steel hose
  6. Anti-leak design to prevent water from leaking after turning off the showerhead.
  7. Powerful and consistent water flow, and if possible, with different spray options

Conclusion

Showering with weak streams of water is not only uncomfortable but also time-wasting and frustrating. 

To overcome such a challenge, you can install a low-pressure showerhead. And today, there is a wide selection of such shower heads that would increase the pressure and deliver powerful and comfortable streams of water.

Categories
Bath Maintenance Tankless Water Heaters

Can I Install a Water Heater Myself?

Disclaimer: This post contains affiliate links for which I earn a commission.

Note: Before starting, click here to open a new tab in Amazon to search for any tools or equipment that you might need.

Today, there are many offline and online tutorials and videos that provide step-by-step guides on how to install water heaters. While the information makes it look like it is easy to do the installation, it might not be a good idea to do it yourself, especially if you have never done it before. 

Most often, the tutorials will give you step-by-step instructions based on an ideal situation. However, your environment and skills are also vital and will determine how you do the work. Moreover, it is not just the physical placement; there are various issues such as the electrical system, gas piping system, venting, access, and other factors that determine performance, reliability, and safety. 

Ideally, it is advisable to seek professional help, especially if you do not have the necessary technical skills. However, if you have these, you can do the installation as long as you ensure that you adhere to all the codes, regulations, and safety precautions. 

Generally, the installation process of a hot water system is a multi-disciplinary exercise that requires knowledge in plumbing, electrical, safety, and others. Additionally, in some countries, you need to comply with relevant codes and obtain permits to perform the work. That said, while you can install the small point-of-use tankless water heaters and especially the plug-in types, you need to consider engaging a professional installer when you have large multi-user water heaters.

Risks of installing a water heater incorrectly

While proper installation and regular maintenance ensure safe and reliable operations, the system will fail when it reaches its end of service life. However, a wrong installation is risky and more dangerous than a normal failure.

Hot water systems are dangerous

Usually, problems with the electrical or gas systems are dangerous and can lead to short circuits, explosions, fires, and other situations. If you are replacing an older system, you need to safely remove it and prepare the space for the new water heater. The heaters use an energy source. This could be gas, electricity, or both, and you must ensure the safe and reliable infrastructure to safely deliver these to the heater system. Incorrect wiring could cause electric shocks or fires. Also, if your heater is propane or natural gas-powered, you need proper piping and connections, otherwise, a minor leak from poor installation may lead to fire risks and explosions. 

Also, failure to install the water heater properly could lead to pressure build-up and tank explosion. 

Voiding warranty

Most manufacturers and even insurance policies will only honor claims for systems installed according to set requirements. In most cases, they require a professional and licensed plumber or installer. Failure to do this will void the warranty or insurance cover.

Time factor

Even when you have technical skills in other fields, installing some water heater models is quite involving and may take you longer than what you save by avoiding a professional. 

Generally, installing your water heater improperly and failing to comply with relevant plumbing, building, and electrical codes could expose yourself and your family to financial, safety, and legal risks. For the above and other reasons, you may need to think twice about installing a water heater by yourself. While you will save some money, the benefits may not warrant taking the risk.

To determine if you can install your water heater by yourself, below is a typical guide on how to perform the replacement or a new installation of an electric-powered model.

How to install a water heater 

If you decide to install the water heater, below are some of the basic steps. Please note that these may vary from one type and model of a water heater to another. Other factors that affect the installation procedure include the type of fuel, whether gas or electric, tank or tankless, capacity, outdoor or indoor, and other issues. While you can install some small models such as the point of use (POUs) and other low-demand models, the procedures may be complex for larger models.

Tools to install a water heater

Below is a list of tools to do the installation.

  • A set of screwdrivers
  • Wrench
  • Flexible hoses
  • Pipe cutter
  • Plumbers tape
  • Voltage detector
  • Soldering iron or torch
  • Solder wire
  • Solder flux
  • Sandpaper cloth, dielectric connectors, etc. (optional)

Step by step instructions on how to install an electric water heater

In our guide, we are assuming that you are replacing a defective system. You will, therefore, first remove the old one and then install the new heater.

Switch off the electrical supply to the water heater

Before working on the water heater, disconnect the power at the panel. Ideally, switch off the water heater’s circuit breaker. Use a voltage detector to ensure that the wires at the heater do not have any power. 

electric circuit breaker

Empty the tank 

If you are replacing a storage-based water heater, empty the tank by

  • Open one of the hot water outlets and letting the water run until it is cold.
  • Afterward, turn off the water heater cold water supply.
  • Use the drain valve to remove all the water from the tank. You may use a hosepipe to pour the water outside or into a sink.
  • To drain the tank faster and allow air to move in, open the hot water faucet and the T&P valve.

Physically disconnect the electrical wires

To avoid confusion, sketch the wiring diagram before removing the wires. If possible, take a photo of the wiring before disconnecting. 

Remove the electrical wires supplying the water heater. Before touching the cables, confirm again that the circuit breaker is off and that they are not carrying any current. As you remove each wire, ensure that you label or mark them appropriately.

Detach the water pipes 

Remove both the water input and output pipes. If the pipe is damaged, you may cut the pipe, but leave as much of the good part as possible. However, if the pipe is still in a good position, you can use it with the new unit, and you need to remove it carefully.

Replace the water heater

Remove the old empty water heater and move it out of the way.

Place the new heater and align it well so that electrical and plumbing connections will fit properly

Prepare the pipes

You need to prepare the old pipes by thoroughly cleaning them with sandpaper. Clean the ends that will connect to the new heater until they are shiny and free of rust and other debris.

Connect the electrical wires

Use the wiring diagram provided by the manufacturer to connect the electrical wires. Ensure that you have grounded the tank by connecting the green wire appropriately. Once done, cover the junction box securely.

install a water heater

Attach the water supply lines

  • With the unit aligned correctly, attach the cold and hot water pipes in their respective positions. 
  • If not already in place, a good practice is to use flexible hoses to attach the heater inlet and outlet and the cold and hot water copper pipes, respectively. The flexibility enhances safety and especially in case of an earthquake. When making connections use the plumber’s tape to line the threads and ensure tight bonding.
  • Open the nearest hot water faucet and turn on the cold water supply to the water heater.
  • Check for leakages, and if none, continue and fill the tank with water. 

Connect the temperature and pressure discharge pipe

  • Use the appropriate fitting to attach the discharge pipe to the T&P valve.
  • Ensure that the pipes’ ends and fittings are clean before attaching them.
  • You may use the solder to make the connections. 

Reconnect the electrical power supply 

Once you fill the tank with cold water, switch on the circuit breaker at the service. If all is well and the connections are correct, the power should reach the water heater. If there is no electrical power on the water heater, turn off the breaker before checking the wiring.

NB: Do not apply the power when the tank does not have enough water since this will cause the heating elements to dry fire and burn if not fully submerged. 

Supply all the hot water lines

Open each hot water outlet and let the water run for some time until it stops sputtering. Doing this removes the air from the tank and pipes.

Set the temperature at about 120 degrees Fahrenheit let the water heat for some time. The process may take a few hours to heat and reach the set temperature. While in the process, monitor the discharge pipe. If it starts dripping, know that the pressure could be too high and make the necessary adjustments.

While this guide assumes that you are replacing an old water heater, it is also applicable if you have a new unit. If installing the new system, skip the first five steps and start at step 6.

Common mistakes to avoid when installing a water heater

While the installation may vary depending on the type of water heater, energy source, environment, and other factors, there are some common mistakes that you should avoid. These include;

Incorrect water heater sizing

It is vital to ensure that the water heating system is the right size. Otherwise, a small unit will need to run for a much longer time, hence wear out much faster. 

install water heater

Similarly, a much larger system will cost more in terms of purchase and running costs. Additionally, it will take up more space and more costly accessories.

Placing the gas or electrical power shut-offs out of site

These controls must be in easy to access and visible locations for normal operations and handling emergencies. They allow you to cut off the electrical supply or flow of the gas into the tanks.  

In practice, you should never heat an empty tank. However, if the shut-off is inaccessible, it means that you must leave it on, even before you complete the installation and added water to the tanks. Consequently, immersion heating elements, which must work when in water, will overheat and burn out. Similarly, if you apply a flame to an empty tank, it will overheat and crack the tank.

Installing the water heater in a difficult location

A difficult-to-access location can be a challenge when installing and maintaining the water heater. Additionally, it may be risky to work in such as place and could also pose other hazards. Usually, the building codes recommend the minimum dimensions you require to access the water heater. They also specify the minimum floor space required to install the heater. Failure to adhere to the building codes results in difficulty installation and challenges in putting the units and tank in and out of the tight spaces.

Loose gas supply pipes and electrical wires

Ideally, you need to secure the electrical power and gas supply lines to the walls and floors to minimize vibrations, loose connections, movements, and associated risks. Also, ensure that they are out of the way from other objects to prevent damage. Where necessary, protect the lines, such as using the appropriate conduit or trunking for the electrical wires.

Other errors include

  • Mixing different metals: – increases the risk of galvanic corrosion. In case there is a need to use two types of metals. Separate them with a dielectric connector to avoid direct contact.
  • Ineffective venting of the exhaust gases in gas-powered based water heaters
  • Replacing a good and serviceable water heater
  • Poor soldering
  • Installing the wrongly sized water heater, etc

Conclusion

While, in most cases, nothing prevents you from installing your water heater, you need to understand what is involved, the risks and impact of your actions. What you need to know is that installing the water heater is not an average DIY project, and could lead to serious performance and safety issues. The installation requires a broad set of skills, including plumbing, electrical, ventilation, carpentry, and more, depending on the environment and where you are installing the system.